Clean Joints Trowel Chart

For one goal: the least thinset to dig out of grout lines. Assumes you floated or self-leveled first, so the floor and walls are flat. Flat substrate is what lets you run small notches.

The one ruleSmallest notch on the wall or floor, plus a thin flat skim on the tile back where the chart calls for it. Bare spots? Skim heavier first. Go up a notch only as a last resort. Bigger notch means more squeeze-up.

The chart

Pill = how much squeeze-up to expect if you do nothing special.

Mosaic sheets

1.5" hex, other sheet mosaics, 11×13 sheets. Walls and floors.

High
3/16 × 5/32 V
  • Comb it, then knock the ridges flat with the smooth side of the trowel.
  • Lay the sheet, then press it in with a grout float or beating block. No fingers.
  • Most joint cleanup comes from these. Check every sheet edge as you go.

Subway, walls

3×6, 3×8, 4×8. Longer pieces like 4×12 go up one size.

Medium
3/16 × 5/32 V4×12 and up:1/4 × 1/4 sq
  • Skim each tile back flat with the margin trowel.
  • Use a non-sag thinset so you're not fighting slide.

4×4 to 6×6 squares

Ceramic or porcelain.

Medium
Walls:3/16 × 5/32 VFloors:1/4 × 1/4 sq
  • Floors get the skim on every tile back. Walls only if a pulled tile shows bare spots.

Quarry tile

6×6 or 8×8. Thick, uneven backs, wide joints.

Low
1/4 × 3/8 sq12×12 quarry:1/2 × 1/2 sq
  • Always skim the back; quarry backs are rough. Wide joints make wet cleanup a quick swipe.

11×13 solid tile

If it's a mosaic sheet, use the mosaic row instead.

Low
1/4 × 3/8 sq
  • Skim the back. Set and slide across the ridges.

12×24

Walls and floors.

Low
3/8" Euro notchor1/4 × 1/2 U
  • Use a large-format (LHT) mortar. Skim every back. Use leveling clips.
  • Few joints, so squeeze-up is easy. Corners with no mortar are the real risk here.

Every batch

  1. Mix it stiffPeanut butter. Ridges hold their shape and don't slump. Let it slake, then remix. Runny thinset squeezes up no matter the notch.
  2. Spread only what you set in 10 minutesSkinned thinset makes you push harder, and pushing harder sends it up the joints.
  3. Stop 1/2" short of tile already setThe new tile spreads the mortar into that gap. Combing tight to the last tile is where squeeze-up starts.
  4. Comb straight lines, one directionHold the trowel at 45°. No swirls. Flatten the ridges for mosaics.
  5. Skim the tile back, set, slide across the ridgesMosaics: press with a float. Big tile: wiggle it down and clip it.
  6. Clean joints now, not tomorrowEvery 15 minutes, run a utility knife or toothbrush down fresh joints. Wet thinset takes seconds. Dry thinset takes an afternoon.
  7. Pull one tile at the start of each tile typeLooks covered? Stop checking. Bare spots? Skim the back heavier before you go up a notch.

Buy this

3/16 × 5/32 VMosaics, subway, small wall tile
1/4 × 1/4 squareSmall floor tile, longer subway
1/4 × 3/8 squareQuarry tile, 11×13
3/8" Euro notch or 1/4 × 1/2 U12×24
Margin trowelSkimming backs, mixing, edges
1/2 × 1/2 squareOnly if your quarry tile is 12×12

Cleanup kit: grout float or beating block, utility knife, stiff toothbrush, leveling clips for 12×24, a bucket of clean water and a sponge.

If it goes wrong

You seeDo this
Thinset coming up in every jointMix stiffer, flatten ridges, or drop one notch size.
Bare spots on a pulled tileHeavier skim on the back. Only then go up a notch.
Mosaic pieces sinking or sitting unevenMix stiffer and press with the float, not your fingers.
Thinset already hard in jointsGrout saw or oscillating tool before grouting. Grout can't cover it.
Hollow-sounding 12×24 cornerPull it now while you still can. Heavier skim, reset.

Coverage targets, for reference: about 80% contact in dry areas and 95% in showers and wet floors, with corners and edges supported. Walls tolerate less than perfect. Floors set with 12×24 or larger tile and anything in a shower don't.